Home > POWER TOOLS & ACC > POWER NAIL GUNS & STAPLERS > BRAD & FINISH GUNS - CORDLESS > FINISH NAIL GUNS - ANGLE
Sort By:
Page of 1
NAILER FINISH GEN2 M18 15GAUGE FINISH NAILER 20V 16GA CORDLSS NAILER ANGL FNSH 20V 15GA BARE
Our M18 FUEL? 15 ga finish nailer provides peak productivity at your jobsite, delivering unmatched nailing performance without the hassle of a compressor and hose. Leveraging our nitrogen air spring mechanism, the 15 ga finish nailer allows you to consistently sink nails to your required depth in hard and soft woods while leaving clean nail holes, making for repeatable results and easy filling. The nitrogen air spring mechanism, combined with our POWERSTATE? brushless motor and REDLINK PLUS? intelligence, delivers a pneumatic-like nailing response with zero ramp-up time from nail to nail, keeping you productive and efficient throughout your job. This cordless finish nailer features a compact and ergonomic design providing access into tight spaces where nailing is required while limiting fatigue when using the tool. When paired with an M18? REDLITHIUM?? CP2.0 battery pack, this battery powered nailer fires up to 750 nails per charge and is fully compatible with all M18? REDLITHIUM? batteries. The Milwaukee? M18 FUEL? 15 ga finish nailer delivers the pneumatic performance that professional carpenters and remodelers demand, with the freedom and convenience of cordless. The DeWALT? DCN660 16 ga angled finish nailer drives 16 ga angled finish nails from 1-1/4 to 2-1/2 in which makes it ideal for fastening crown molding, casing and baseboards. With its brushless motor powered by a DeWALT? 20 V Max Lithium-Ion battery the DCN660 is ready to go to work without the hassle of using gas, compressor and hose. Tackle jobs both large and small with the features of a pneumatic tool and the freedom of cordless. Maximum initial battery voltage (measured without a workload) is 20 V. Nominal voltage is 18 V. The DeWALT? DCN650 15 ga angled finish nailer drives 15 ga angled finish nails from 1-1/4 to 2-1/2 in which makes it ideal for fastening crown molding, casing, baseboards and hardwood floor installation. With its brushless motor powered by a DeWALT? 20 V Max Lithium-Ion battery the DCN650 is ready to go to work without the hassle of using gas, compressor and hose. Tackle jobs both large and small with the features of a pneumatic tool and the freedom of cordless. Maximum initial battery voltage (measured without a workload) is 20 V. Nominal voltage is 18 V.
KIT NAILER FINSH GEN2 M18 15GA KIT NAILER STRT M18 FUEL 16GA NAILER FINISH ANGLED 16GA 20V
The M18 FUEL? 16 ga straight finish nailer delivers on the promise of peak productivity at your worksite, providing unmatched driving power, speed and efficiency with practically no set up and minimal maintenance. Using the exceptional application speed, power and durability of our compact POWERSTATE? brushless motor, plus our ready to fire cylinder design, this tool is capable of fully sinking 2-1/2 in nails into solid oak with zero ramp-up time. This 18 V Nailer operates from the revolutionary REDLITHIUM? Battery for unbeatable strength and run time, eliminating the mess and cost of gas cartridges. It also includes REDLINK PLUS? Intelligence, the most advanced electronic system on the market, to prevent damage to the nailer and battery from overloading and overheating. The M18 FUEL? nailer not only primes you for top performance, it also creates the experience of a pneumatic nailer that professional carpenters and remodelers expect, without the hassle of compressors and hoses. The DeWALT? DCN660 16 ga angled finish nailer drives 16 ga angled finish nails from 1-1/4 to 2-1/2 in which makes it ideal for fastening crown molding, casing and baseboards. With its brushless motor powered by a DeWALT? 20 V Max Lithium-Ion battery the DCN660 is ready to go to work without the hassle of using gas, compressor and hose. Tackle jobs both large and small with the features of a pneumatic tool and the freedom of cordless. Maximum initial battery voltage (measured without a workload) is 20 V. Nominal voltage is 18 V.
NAILER ANGLED FINISH 20V 15GA
The DeWALT? DCN650 15 ga angled finish nailer drives 15 ga angled finish nails from 1-1/4 to 2-1/2 in which makes it ideal for fastening crown molding, casing, baseboards and hardwood floor installation. With its brushless motor powered by a DeWALT? 20 V Max Lithium-Ion battery the DCN650 is ready to go to work without the hassle of using gas, compressor and hose. Tackle jobs both large and small with the features of a pneumatic tool and the freedom of cordless. Maximum initial battery voltage (measured without a workload) is 20 V. Nominal voltage is 18 V.